//增加eNodeB功能
ADD ENODEBFUNCTION: eNodeBFunctionName="FDD eNodeB118", ApplicationRef=1, eNodeBId=118;
//设置网元(NE)配置属性
SET NE: NENAME="FDD eNodeB118", SITENAME="FDD eNodeB118";
//添加运营商
ADD CNOPERATOR: CnOperatorId=0, CnOperatorName="China Telecom", CnOperatorType=CNOPERATOR_PRIMARY, Mcc="460", Mnc="00";
//增加跟踪区域标识
ADD CNOPERATORTA: TrackingAreaId=0, CnOperatorId=0, Tac=118;
//设置网元工程状态
SET MNTMODE: MNTMODE=NORMAL;
//增加机柜，型号是BBU3900
ADD CABINET: CN=0, TYPE=VIRTUAL;
ADD SUBRACK: CN=0, SRN=0, TYPE=BBU3900;
//增加主控板UMPT，必配，一般在第7槽，这里是在第6槽
ADD BRD: SN=6, BT=UMPT;
//增加LBBP单板LBBP，必配，一般在第3槽
ADD BRD: SN=3, BT=LBBP;
//增加FAN，第16槽
ADD BRD: SN=16, BT=FAN;
//增加UPEU，一般在第19槽
ADD BRD: SN=19, BT=UPEU;
//增加RRU链
ADD RRUCHAIN: RCN=0, TT=CHAIN, BM=COLD, AT=LOCALPORT, HSRN=0, HSN=3, HPN=0;
//增加RRU
ADD RRU: CN=0, SRN=90, SN=0, TP=TRUNK, RCN=0, PS=0, RT=MRRU, RS=LO, RXNUM=1, TXNUM=1;
//设置网元的本地时区和夏令时
SET TZ: ZONET=GMT-0800, DST=NO;
//设置时间源
SET TIMESRC: TIMESRC=NTP;
//增加GPS
ADD GPS: SRN=0, SN=6, CABLE_LEN=30, PRI=4;

//设置系统时钟
SET CLKMODE: MODE=FREE;
SET CLKSYNCMODE: CLKSYNCMODE=FREQ;

//-----EnodeB传输数据配置----重点
//增加以太网端口
ADD ETHPORT: SN=6, SBT=BASE_BOARD, PA=COPPER, SPEED=AUTO, DUPLEX=AUTO;
//增加IP地址
ADD DEVIP: SN=6, SBT=BASE_BOARD, PT=ETH, PN=0, IP="172.28.1.118", MASK="255.255.255.0";
//增加静态IP路由
ADD IPRT: RTIDX=2, SN=6, SBT=BASE_BOARD, DSTIP="172.28.4.4", DSTMASK="255.255.255.255", RTTYPE=NEXTHOP, NEXTHOP="172.28.1.1";
ADD IPRT: RTIDX=1, SN=6, SBT=BASE_BOARD, DSTIP="172.28.5.5", DSTMASK="255.255.255.255", RTTYPE=NEXTHOP, NEXTHOP="172.28.1.1";

//端点模式-增加端点节点组
ADD EPGROUP: EPGROUPID=0;
//增加用户面本端对象
ADD USERPLANEHOST: UPHOSTID=0, IPVERSION=IPv4, LOCIPV4="172.28.1.118", IPSECSWITCH=DISABLE;
//增加用户面对端对象
ADD USERPLANEPEER: UPPEERID=0, IPVERSION=IPv4, PEERIPV4="172.28.5.5", IPSECSWITCH=DISABLE;
//增加SCTP本端对象
ADD SCTPHOST: SCTPHOSTID=0, IPVERSION=IPv4, SIGIP1V4="172.28.1.118", SIGIP1SECSWITCH=DISABLE, SIGIP2SECSWITCH=DISABLE, PN=36412, SCTPTEMPLATEID=0;
////增加SCTP对端对象
ADD SCTPPEER: SCTPPEERID=0, IPVERSION=IPv4, SIGIP1V4="172.28.4.4", SIGIP1SECSWITCH=DISABLE, SIGIP2SECSWITCH=DISABLE, PN=36412;
//将SCTP本端/对端加入到端点组中
ADD SCTPHOST2EPGRP: EPGROUPID=0, SCTPHOSTID=0;
ADD SCTPPEER2EPGRP: EPGROUPID=0, SCTPPEERID=0;
//将用户面本端/对端加入到端点组中
ADD UPHOST2EPGRP: EPGROUPID=0, UPHOSTID=0;
ADD UPPEER2EPGRP: EPGROUPID=0, UPPEERID=0;
//添加S1配置
ADD S1: S1Id=0, CnOperatorId=0, EpGroupCfgFlag=CP_UP_CFG, CpEpGroupId=0, UpEpGroupId=0;

//---------EnodeB无线数据配置-----
//增加扇区及扇区天线
ADD SECTOR: SECTORID=0, SECNAME="ENB118CELL_0", ANTNUM=1, ANT1CN=0, ANT1SRN=90, ANT1SN=0, ANT1N=R0A, CREATESECTOREQM=FALSE;
//增加小区
ADD CELL: LocalCellId=0, CellName="ENB118CELL_0", FreqBand=7, UlEarfcnCfgInd=NOT_CFG, DlEarfcn=2850, UlBandWidth=CELL_BW_N100, DlBandWidth=CELL_BW_N100, CellId=118, PhyCellId=118, FddTddInd=CELL_FDD, RootSequenceIdx=0, CustomizedBandWidthCfgInd=NOT_CFG, EmergencyAreaIdCfgInd=NOT_CFG, UePowerMaxCfgInd=NOT_CFG, MultiRruCellFlag=BOOLEAN_FALSE, CrsPortNum=CRS_PORT_1, TxRxMode=1T1R;
//增加扇区设备
ADD SECTOREQM: SECTOREQMID=0, SECTORID=0, ANTNUM=1, ANT1CN=0, ANT1SRN=90, ANT1SN=0, ANT1N=R0A, ANTTYPE1=RXTX_MODE;
//将小区绑定运营商
ADD CELLOP: LocalCellId=0, TrackingAreaId=0, MMECfgNum=CELL_MME_CFG_NUM_0;
//激活小区
ACT CELL: LocalCellId=0;